LogoOC 4 
  • KÄRCHER Home & Garden App
  • Safety instructions
    • Hazard levels
    • Risk of electric shock
    • Charger
    • Device with built-in battery
    • Safe handling
  • Intended use
  • Environmental protection
  • Accessories and spare parts
  • Scope of delivery
  • Safety devices
    • ON/OFF button
    • Pressure switch
    • Motor circuit breaker
  • Device description
    • Overview of the device
    • LED codes
  • Initial startup
    • Removing the device from the water reservoir
    • Battery charging
    • Water supply
      • Establishing a water supply from the device's water reservoir
      • Suck water from open containers
  • Operation
    • Mounting the Multi Jet nozzle
    • Set spray type
    • Installing accessories
    • Operation without detergent
    • Operation with detergent
  • Interrupting operation
  • Ending operation
  • Transport
    • Manual transportation
    • Transport in vehicles
  • Care and maintenance
    • Cleaning the fine filter
    • Replacing / disposing of the battery
  • Troubleshooting guide
    • The device does not run.

    • Device does not reach required pressure.

    • Strong pressure fluctuations or constant switching off / on of the device.

    • The device is leaking.

  • Warranty
  • Declaration of Conformity
  • Technical data

      OC 4 

      92222210 (02/26)

      KÄRCHER Home & Garden App

      With the KÄRCHER Home & Garden app, you benefit from the following advantages when using your device:

      • Application tips & expert knowledge

      • Product information, overview of accessories and operating instructions

      • Support and service contact

      • Online shop - exclusive offers and much more

      Scan the code on the packaging or download the KÄRCHER Home & Garden app from your app store and conveniently register your product.

      Safety instructions

      Read this safety chapter and these original instructions before using the device for the first time. Act in accordance with them. Keep the original instructions for future reference or for future owners.

      • In addition to the notes in the operating instructions, you also need to take into consideration the general safety regulations and accident prevention guidelines applicable by law.

      • Warnings and information notices attached to the device provide important information for hazard-free operation.

      Hazard levels

      DANGER

      Indication of an imminent threat of danger that will lead to severe injuries or even death.

      WARNING

      Indication of a potentially dangerous situation that may lead to severe injuries or even death.

      CAUTION

      Indication of a potentially dangerous situation that may lead to minor injuries.

      ATTENTION

      Indication of a potentially dangerous situation that may lead to damage to property.

      Risk of electric shock

      DANGER

      Do not direct the spray jet directly onto consumables containing electrical components, e.g.the interior space of ovens.

      WARNING

      The device and the charger contain electrical components – do not clean the device and the charger under running water.

      Charger

      DANGER

      Never touch the mains plug and socket with wet hands.

      DANGER

      Danger of explosion. Do not charge any non-rechargeable battery.

      DANGER

      Do not charge the battery pack in an explosion-hazard environment.

      DANGER

      Never insert conductive objects, e.g. screwdrivers or similar, into the charging socket on the appliance.

      WARNING

      Only charge the appliance using the original charger enclosed or with a charger approved by KÄRCHER.

      WARNING

      Protect the power cable from heat, sharp edges, oil and moving parts.

      WARNING

      Do not open the charger. Repairs are only to be carried out by qualified personnel.

      WARNING

      Only use the charger to charge approved batteries.

      WARNING

      Immediately replace a damaged charger together with charging cable with an original part.

      WARNING

      The appliance contains electrical components - do not clean the appliance under running water.

      WARNING

      You may not charge the battery pack for longer than 24 hours without interruption.

      CAUTION

      Do not use the battery pack when dirty or wet.

      CAUTION

      Keep the charger ventilation slits free of obstructions.

      CAUTION

      Do not pull the mains plug out the socket using the power supply cable.

      CAUTION

      Do not carry/transport the device using the power supply cable.

      ATTENTION

      Short circuit hazard. Protect the contacts of the battery pack from metal parts.

      ATTENTION

      Only use and store the charger in dry rooms.

      Device with built-in battery

      DANGER

      Never touch contacts or lines.

      DANGER

      Batteries can be swallowed by children or persons with reduced physical, sensory or mental capabilities due to lack of experience or knowledge. Keep batteries out of the reach of children and these persons. Swallowing a battery is an emergency that requires immediate medical treatment.

      DANGER

      Do not expose the device and battery to strong sunlight, heat or fire.

      DANGER

      Danger of explosion. Do not charge non-rechargeable batteries.

      WARNING

      Do not charge any damaged batteries. Replace damaged or degraded batteries with batteries approved by KÄRCHER.

      WARNING

      Leaking battery fluid may cause skin irritation, burns, or eye damage. Batteries contain toxic substances that can cause health problems if swallowed or inhaled. Always wear gloves when handling a leaking battery to avoid skin contact. If the spilled liquid has come into contact with skin or eyes, rinse the affected areas immediately and thoroughly with water and seek medical advice.

      WARNING

      Short-circuiting the battery terminals (+/-) can lead to an explosion and ignition. Do not short-circuit the terminals (+/–) on the battery or the device. Do not store batteries in metal containers or with other metal parts.

      CAUTION

      Batteries contain hazardous substances that can cause serious environmental damage. Do not dispose of batteries with household rubbish, but properly at a collection point or recycling centre.

      ATTENTION

      Fully charge the battery before using the device for the first time.

      ATTENTION

      Remove used or defective batteries from the device and dispose of them according to local regulations.

      ATTENTION

      The battery compartment of the device is technically secured against accidental opening. Open and close the battery compartment as described in the operating instructions for the device.

      ATTENTION

      Do not use damaged or modified batteries.

      ATTENTION

      When installing batteries, ensure the correct polarity (+/-) according to the markings in the battery compartment or on the electrical plug connections.

      Safe handling

      WARNING

      The device is not intended for use by children, persons with restricted physical, sensory or mental abilities or persons unfamiliar with these instructions.

      WARNING

      Persons with reduced physical, sensory or mental capabilities and persons lacking experience and knowledge may only use the appliance if they are properly supervised, have been instructed on use of the appliance safely by a person responsible for their safety, and understand the resultant hazards involved.

      WARNING

      Children must not play with the appliance.

      WARNING

      Children must be supervised to prevent them from playing with the appliance.

      WARNING

      Only use the device for its proper use. Take into account the local conditions and beware of third parties, in particular children, when working with the device.

      WARNING

      Adhere to the respective safety regulations in hazard zones (e.g. service stations). Never operate the device in explosive spaces.

      WARNING

      Do not spray any objects which contain harmful substances (e.g. asbestos).

      WARNING

      Risk of injury. Do not direct the spray jet onto the eyes.

      CAUTION

      Do not use the appliance if it has been dropped beforehand, is visibly damaged or if it is leaking.

      CAUTION

      Only operate or store the device in accordance with the description or figure.

      CAUTION

      Never leave the device unsupervised while it is in operation.

      CAUTION

      In order to guarantee stability, place the device on a firm, flat surface.

      CAUTION

      Accidents or damage due to the device falling over. Before all actions with or on the device, you must make sure that it is stable.

      ATTENTION

      Do not fill with any cleaning agents or other supplements.

      ATTENTION

      Device damage. Never fill the water reservoir with solvents, liquids containing solvents or undiluted acids (e.g. detergents, petrol, paint thinners and acetone).

      ATTENTION

      Device damage due to dry running. Only switch on the device when water is present in the water reservoir.

      ATTENTION

      Do not operate the device at temperatures below 0 °C.

      Intended use

      Use the low pressure cleaner in private households only.

      The low pressure cleaner is intended for cleaning machines, vehicles, tools, façades, terraces, garden machines, pets etc. using a low-pressure water stream without additional detergents.

      Environmental protection

      The packing materials can be recycled. Do not dispose of packaging as household rubbish but place it in recycling.

      Electrical and electronic devices contain valuable recyclable materials and often components such as batteries, rechargeable batteries, battery packs and lubricants. These can pose a potential risk to health and the environment if handled or disposed of incorrectly. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

      Remove batteries, rechargeable batteries and battery packs from the old devices. The removal of these parts is described in the operating instructions. Dispose of the battery separately via suitable collection systems.

      Cleaning work that produces oily waste water (e.g. engine washing, underbody washing), may only be carried out at washing stations with oil separators.

      Work with detergents may only be carried out on liquid-tight work areas with a connection to the sewage system. Do not allow detergents to penetrate water or soil.

      Water removal from public waters is not allowed in some countries.

      Notes on the content materials (REACH)

      Current information on content materials can be found at: www.kaercher.de/REACH

      Accessories and spare parts

      Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

      Information on accessories and spare parts can be found at www.kaercher.com.

      Scope of delivery

      The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

      Safety devices

      CAUTION

      Risk of injury and damage due to missing or modified safety devices.

      Injuries and material damage

      Safety devices must not be bypass, removed or rendered ineffective. Safety devices are provided for your own protection.

      ON/OFF button

      The ON/OFF button prevents unintentional operation of the device.

      Pressure switch

      If the trigger of the low pressure gun is operated, the pressure switch turns on the pump and the low pressure stream is released.

      If the trigger is operated again and released, the pressure switch turns off the pump and the low pressure stream is stopped.

      Motor circuit breaker

      The motor circuit breaker shuts off the device if power consumption it too high.

      Device description

      Overview of the device

      Illustrations are examples, colours and details may vary.


      1. Cap (4 pieces)
      2. Carrying handle on the cover
      3. Filler plug
      4. Cover
      5. Water reservoir
      6. Valve opener
      7. Fine filter (device)
      8. Battery compartment cover
      9. Battery
      10. Type plate
      11. * Suction hose
      12. * Suction hose hub
      13. * Suction strainer
      14. * Fine filter (suction hose)
      15. * Bayonet sleeve
      16. Charger
      17. Charging cable
      18. USB-C plug
      19. USB-A plug
      20. Bar cover
      21. Charging socket
      22. LED
      23. ON/OFF button
      24. Device
      25. Carrying handle on the device
      26. Low pressure hose
      27. Low pressure gun
      28. Trigger
      29. Lock nut
      30. Multi Jet nozzle

      * Optionally available

      LED codes

      LED colour green
      The battery is charging (LED pulsates).
      The device is switched on, charge state ≥ 50 % (LED lights up).
      LED colour orange
      The device is switched on, charge state 20% -50% (LED lights up).
      Warning of low remaining running time of approx. 4 min. (LED pulsates).
      The battery is fully discharged (LED flashes slowly for 5 seconds).
      Malfunction (LED flashes quickly for 20 seconds), see Troubleshooting guide.

      Initial startup

      1. ATTENTION

        Risk of damage and leaks when parking in wet conditions, dirt and on loose surfaces.

        Damage and leaks on the device and water reservoir

        Do not place the device in wet conditions,e.g. puddles or damp grass.Do not place the water reservoir on a dirty, loose surface,e.g. sand or mud.

        Place the device on a level, horizontal surface.

      Removing the device from the water reservoir

      1. Remove the cover:

        1. Disengage both top caps and unhook them from the cover.

        2. Remove the cover.


      2. Remove the charger and the charging cable from the water reservoir.

      3. Remove the device from the water reservoir:

        1. Fold up the carrying handle on the device.

        2. Lift the device out of the water reservoir:


        Inserting the device in the water reservoir is performed in the reverse sequence.

      Battery charging

      1. Charging the battery:

        1. Release the cover of the charging socket from the device and swing it downwards.

        2. Plug the USB-C plug of the charging cable into the charging socket.

        3. Plug the USB-A plug of the charging cable into the charger.

        4. Plug the charger into a mains socket.


        Note

        The LED pulsates green during the charging process. It lights up for 10 min. green when the battery is fully charged.

        For the charging time, see Technical data.

      2. After charging

        Note

        Avoid unnecessary energy consumption and unplug the charger once the battery is fully charged.

      3. Pull the charger out of the mains socket.

      4. Pull the USB-C plug out of the charging socket.

      5. Swivel the cover of the charging socket upwards and press it firmly on the device.

      Water supply

      ATTENTION

      Risk of damage due to improper water supply.

      Damage to the device and accessories

      Only fill the water reservoir with clean, clear water.Only allow the device to draw in clean, clear water.Do not fill the water reservoir with detergents, pesticides, or other additives. Do not use the device to suction such substances.Do not immerse the device in liquids.Do not use the water reservoir to draw liquids while it is attached to the device.Remove the water reservoir from the device before filling it with water.

      Establishing a water supply from the device's water reservoir

      1. Fill the water reservoir:

        1. Attach the cover to the water reservoir.

        2. Engage both top caps on the cover and hook them in.

        3. Remove the filler plug from the cover and lift it up.

        4. Fill the water reservoir with clean, cold clear water.


      2. Fold down the filler plug and press down.

      3. Place the low-pressure gun next to the device.

      4. Attach the water reservoir to the device:

        1. Place the low-pressure hose into the recess on the device to avoid pinching it.

        2. Place the water reservoir on the device and engage both lower caps.


      5. Remove the water reservoir from the device to refill it with water.

      Suck water from open containers

      1. ATTENTION

        Function failure if the valve opener is not fitted.

        No pump function

        Keep the valve opener and the fine filter in a safe place to avoid losing them.Insert the fine filter and the valve opener into the device before operating it with the water reservoir. Make sure that the pins on the fine filter and valve opener point upwards.

        Lever out the valve opener using the suction hose hub or remove it from the device using pliers.


        Installation information

        The pin on the valve opener must point upwards.

        Align the notch on the valve opener with the guide pin on the device.

      2. Remove the fine filter (device) from the device using the suction hose hub or pliers.


      3. Store the valve opener and the fine filter safely, e.g.in the water reservoir.

      4. Install the suction hose:

        1. Insert the suction hose hub into the device.

        2. Turn the suction hose hub slightly to fix it in place.

        3. Hang the suction strainer in a water source (e.g. water bucket, can).


        Note

        After operation, remove the suction hose in reverse order.

        Install the fine filter and valve opener.

      Operation

      1. Place the device on a level, horizontal surface.

      Mounting the Multi Jet nozzle

      1. Mounting the Multi Jet nozzle on the low-pressure gun:

        1. Press the Multi Jet nozzle into the low-pressure gun and

        2. rotate by 90°.

        3. Tighten the lock nut hand-tight.


        Removal is performed in the reverse sequence.

      Set spray type

      1. WARNING

        Risk of damage when setting the spray type during operation.

        Damage to the Multi Jet nozzle

        Release the trigger of the low-pressure gun before turning the head of the Multi Jet nozzle.

        Turn the head of the multi jet nozzle to set the desired spray type (point jet, flat stream, mist jet, pouring jet).


      Installing accessories

      Various nozzles, brushes etc. are available as accessories for the device.

        Removing the nozzle

      1. Removing the nozzle on the low-pressure gun:

        1. Press the nozzle into the low-pressure gun and loosen it by turning it 90°

        2. and pull it off.


      2. Installing accessories

      3. Installing accessories on the low-pressure gun:

        1. Press the accessory into the low-pressure gun

        2. and fasten it by turning it 90°.

        3. If present, tighten the lock nut hand-tight.


      Operation without detergent

      ATTENTION

      Risk of damage if dry running.

      Pump damage

      Only switch on the device when there is water in the water reservoir or the suction strainer is fully submerged.Switch off the device as soon as the water reservoir or the external water source is empty.Switch off the device if it does not build up pressure within 2 minutes. Then proceed according to the instructions in Troubleshooting guide.
      1. Press the ON/OFF button.

        The device switches on.


      2. CAUTION

        Risk of injury from spray jet.

        Injury to eyes and ears

        Do not aim the spray jet at the eyes or ears of people or animals.

        Pull the trigger to switch on the spray jet.

        The trigger engages and can be released.

        Pull the trigger again and release it to switch off the spray jet.


      3. Carry out the cleaning process:

        1. Pull the trigger to switch on the spray jet.

        2. Carry out the cleaning process.

        3. Pull the trigger and release it to switch off the spray jet.

        Note

        At approx. 20 % remaining running time (see Technical data), the LED starts to pulsate orange. Charge the battery as soon as possible, see Battery charging.

        For further information on the LED, see LED codes.

        If the trigger is not operated for 30 minutes, the device switches off.

      Operation with detergent

      DANGER

      Health hazards due to detergents.

      Serious damage to health

      Observe the detergent manufacturer's safety data sheet.Wear the prescribed personal protective gear.

      ATTENTION

      Risk of damage due to foreign substances in the water reservoir.

      Damage to the device

      Do not fill the water reservoir with detergents, pesticides, or other additives.

      ATTENTION

      Risk of damage from unsuitable detergents.

      Material damage

      Only use detergents that have been approved by KÄRCHER and are suitable for the objects to be cleaned.Observe the safety instructions, dosage recommendations and notes enclosed with the detergents.Use detergents sparingly.

      ATTENTION

      Risk of damage due to prolonged exposure and drying of detergents.

      Material damage

      Do not apply detergent to hot surfaces.Observe the maximum contact time.Do not allow detergent to dry on the surfaces being cleaned.

      Note

      KÄRCHER detergents ensure fault-free, effective operation. Please ask us for advice and observe our catalog or our detergent information sheets.

      1. Spray the detergent sparingly on the dry surfaces and let it work for a while (do not let it dry).

      2. ATTENTION

        Risk of damage if dry running.

        Pump damage

        Only switch on the device when there is water in the water reservoir or the suction strainer is fully submerged.Switch off the device as soon as the water reservoir or the external water source is empty.Switch off the device if it does not build up pressure within 2 minutes. Then proceed according to the instructions in Troubleshooting guide.

        Press the ON/OFF button.

        The device switches on.


      3. CAUTION

        Risk of injury from spray jet.

        Injury to eyes and ears

        Do not aim the spray jet at the eyes or ears of people or animals.

        Pull the trigger and carry out the cleaning process.

        Note

        Approx. 2 min before the end of the operating time (see Technical data), the operating state LED starts flashing. Charge the battery as soon as possible, see Battery charging.

      Interrupting operation

      1. Actuate the trigger and release.

        The spray jet stops.

        After approx. 30 minutes without being pressed, the device shuts off automatically.

      Ending operation

      1. Press the ON/OFF button.

        The device switches off.

      2. Stop the water supply to the device:

        1. Empty out the water remaining in the water reservoir.

          It can,for example, be used for other cleaning purposes or for watering.

          Or:

        2. Remove the suction hose and install the fine filter and valve opener, see Suck water from open containers.

      3. Press the ON/OFF button.

        The device switches on.

      4. Actuate the trigger and wait until no more water is emitted.

      5. Actuate the trigger again and release.

      6. Press the ON/OFF button.

        The device switches off.

      7. Allow the water reservoir to dry completely.

      8. Stow the low-pressure gun and the low-pressure hose on the device.

      9. Place the device in the water reservoir, see Removing the device from the water reservoir.

      10. Stow the charger and the charging cable in the water reservoir.

      11. Attach the lid to the water reservoir.

      Transport

      CAUTION

      Risk of injury or damage due to the weight of the device.

      Injuries and material damage

      Be aware of the weight of the device during transport and storage.

      ATTENTION

      Risk of damage due to frost.

      Damage to the device and accessories

      Empty the water completely from the device and accessories.Always protect the device and accessories from frost.
      1. Observe regulations for dangerous goods during transport.

      Manual transportation

      1. Fold up the carrying handle on the cover and use it to carry the device.

      Transport in vehicles

      CAUTION

      Risk of injury and damage due to tipping or sliding of the device.

      Injuries and material damage

      Before transporting the device in vehicles, secure it against slipping and tipping over in accordance with the applicable guidelines.
      1. Switch off the device.

      2. ATTENTION

        Risk of damage due to escaping water.

        Material damage

        Transport the device upright if water is present in the water reservoir. If the device is not standing upright, water may escape from the ventilation valve.

        Before transporting the device, stow it away or secure it against sliding, tipping and being thrown around.

      Care and maintenance

      DANGER

      Danger of death due to electric shock.

      Fatal or severe injury may occur when touching live electrical parts.

      Do not touch any live parts.Switch off the device.Pull the charger out of the mains socket.

      Cleaning the fine filter

      Clean the fine filters in the device and suction hose regularly.

      ATTENTION

      Risk of damage when operating without a fine filter or with a damaged fine filter.

      Damage to the device and accessories.

      Check the fine filter for damage before installation. Replace a damaged fine filter immediately.Do not clean the fine filter with hard, pointed objects.Do not operate the device without a fine filter.

        Cleaning the fine filter of the device

      1. Remove the water reservoir, see Establishing a water supply from the device's water reservoir.

      2. Remove the valve opener and fine filter, see Suck water from open containers.

      3. Clean the fine filter with clean, flowing water against the direction of flow.


      4. Install the fine filter and valve opener.

      5. Clean the fine filter of the suction hose

      6. Remove and clean the fine filter:

        1. Turn the suction strainer approx. 45° and

        2. pull it off from the bayonet sleeve.

        3. Pull the fine filter off from the bayonet sleeve.

        4. Clean the fine filter and suction strainer with clean, flowing water against the direction of flow.


      7. The installation is performed in the reverse sequence.

      Replacing / disposing of the battery

      Note

      The battery has reached the end of its service life if the device constantly switches off after a short period of operation and the battery needs to be charged.

      Please refer to Environmental protection.

      Replace the battery at the end of its service life.

      Remove the battery before disposing of the device.

      Dispose of the battery separately from the device.

        Removing the battery

      1. Switch off the device, see Ending operation.

      2. Removing the battery:

        1. Unscrew the screws using a screwdriver.

        2. Remove the battery compartment cover.

        3. Take the battery out.

        4. Disconnect the electrical socket plug connections.


      3. Dispose of the battery in the correct manner.

      4. Installing the battery

      5. WARNING

        Risk of explosion and fire if non-approved batteries or battery packs are used.

        Severe injuries and/or material damage

        Replace damaged and worn batteries or battery packs exclusively with batteries or battery packs approved by KÄRCHER.

        Install a new battery in the reverse order.

      Troubleshooting guide

      DANGER

      Danger of death due to electric shock.

      Fatal or severe injury may occur when touching live electrical parts.

      Do not touch any live parts.Switch off the device.Pull the charger out of the mains socket.

      Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorized Customer Service.

      • The device does not run. 

      • Device does not reach required pressure. 

      • Strong pressure fluctuations or constant switching off / on of the device. 

      • The device is leaking. 

      The device does not run.

      Cause:

      The charging state of the battery is too low.

      Remedy:

      1. Charge the battery, see Battery charging.

      Cause:

      The motor is overloaded, the motor circuit breaker has tripped.

      Remedy:

      1. Switch off the device.

      2. Switch on the device and put it into operation.

      Cause:

      The ambient temperature is outside the permissible range, see Technical data, the motor circuit breaker has tripped.

      Remedy:

      1. Switch off the device.

      2. Allow the device to cool down / heat up.

      3. Switch on the device and put it into operation.

        Have the device checked by KÄRCHER Service if this malfunction occurs repeatedly.

      Device does not reach required pressure.

      Cause:

      Not enough water in the water reservoir.

      Remedy:

      1. Make sure that there is enough clean, clear water in the water reservoir.

      Cause:

      The suction hose does not suck in water.

      Remedy:

      1. Make sure that the maximum suction height is not exceeded, see Technical data.

      2. Ensure that there is sufficient clean, clear water in the open container and that the suction strainer is fully immersed.

      Cause:

      The fine filter in the device or in the suction hose is dirty.

      Remedy:

      1. Clean the fine filter, see Cleaning the fine filter.

      Strong pressure fluctuations or constant switching off / on of the device.

      Cause:

      The nozzle is clogged.

      Remedy:

      1. To clean the nozzle: Remove contamination and debris from the nozzle hole, using a needle and rinse with clean, clear water from the front.

      2. Make sure that there is enough clean, clear water in the water reservoir.

      The device is leaking.

      Cause:

      Minor leakage due to technical reasons.

      Remedy:

      1. Minor leakage of the device can occur due to technical reasons and is not a cause for concern.

      Cause:

      Major leakage.

      Remedy:

      1. Contact the authorized Customer Service.

      Warranty

      The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing flaw is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

      Further information can be found at: www.kaercher.com/dealersearch

      Further warranty information (if available) can be found in the service area of your local KÄRCHER website under "Downloads".

      Declaration of Conformity

      EU Declaration of Conformity

      We hereby declare that the product named below complies with the relevant provisions of the directives and regulations listed. This declaration is invalidated by any changes made to the product that are not approved by us. The manufacturer shall bear sole responsibility for issuing of this declaration of conformity.

      Product: Mobile Outdoor Cleaner

      Type: OC 3, OC 3 Plus, OC 3 Foldable, OC 4

      Directives and Regulations

      2006/42/EC (+2009/127/EC) (until 19/01/2027) (EU) 2023/1230 (from 20/01/2027)

      2014/30/EU

      2011/65/EU

      2009/125/EC

      2000/14/EC

      2019/1782

      (EU) 2023/1542

      Harmonised standards used

      EN 55014-1: 2017 + A11: 2020

      EN 55014-2: 1997 + A1: 2001 + A2: 2008

      EN 60335-1

      EN 60335-2-54

      EN 61000-3-2: 2014

      EN 61000-3-3: 2013

      EN 61558-1

      EN 61558-2-16

      EN 62233: 2008

      EN IEC 63000: 2018

      Applied conformity evaluation method

      2000/14/EG: Annex V

      Sound power level dB(A)

      OC 3, OC 3 Plus

      Measured: 81

      Guaranteed: 84

      OC 3 Foldable

      Measured: 77

      Guaranteed: 79

      OC 4

      Measured: 80

      Guaranteed: 82

      Name and address

      Documentation supervisor:

      S. Reiser

      Alfred Kärcher SE & Co. KG

      Alfred-Kärcher-Str. 28 - 40

      71364 Winnenden (Germany)

      Tel.: +49 7195 14-0

      Fax: +49 7195 14-2212


      Winnenden, 2026/03/01

      The undersigned act on behalf of and with the authority of the Board of Directors.

      Alfred Kärcher SE & Co. KG

      Alfred-Kärcher-Str. 28 - 40

      71364 Winnenden (Germany)

      Ph.: +49 7195 14-0

      Fax: +49 7195 14-2212

      UK Declaration of Conformity

      We hereby declare that the product named below complies with the relevant provisions of the directives and regulations listed. This declaration is invalidated by any changes made to the product that are not approved by us. The manufacturer shall bear sole responsibility for issuing of this declaration of conformity.

      Product: Mobile Outdoor Cleaner

      Type: OC 3, OC 3 Plus, OC 3 Foldable, OC 4

      Directives and Regulations

      S.I. 2008/1597 (as amended)

      S.I. 2016/1091 (as amended)

      S.I. 2012/3032 (as amended)

      S.I. 2010/2617 (as amended)

      S.I. 2001/1701 (as amended)

      (EU) 2019/1782

      Designated standards used

      EN 55014-1: 2017 + A11: 2020

      EN 55014-2: 1997 + A1: 2001 + A2: 2008

      EN 60335-1

      EN 60335-2-54

      EN 61000-3-2: 2014

      EN 61000-3-3: 2013

      EN 61558-1

      EN 61558-2-16

      EN 62233: 2008

      EN IEC 63000: 2018

      Applied conformity assessment procedure

      S.I. 2001/1701 (as amended): Schedule 8

      Sound power level dB(A)

      OC 3, OC 3 Plus

      Measured: 81

      Guaranteed: 84

      OC 3 Foldable

      Measured: 77

      Guaranteed: 79

      OC 4

      Measured: 80

      Guaranteed: 82

      Name and address

      Documentation supervisor:

      S. Reiser

      Alfred Kärcher SE & Co. KG

      Alfred-Kärcher-Str. 28 - 40

      71364 Winnenden (Germany)

      Tel.: +49 7195 14-0

      Fax: +49 7195 14-2212


      Winnenden, 2026/03/01

      The undersigned act on behalf of and with the authority of the Board of Directors.

      Alfred Kärcher SE & Co. KG

      Alfred-Kärcher-Str. 28 - 40

      71364 Winnenden (Germany)

      Ph.: +49 7195 14-0

      Fax: +49 7195 14-2212

      Technical data

        

      Electrical connection/Battery
      Nominal voltage of battery
      10,8 V
      Nominal power of device
      49,5 W
      Protection type
      IPX4
      Protection class
      III
      Charger
      Charger mains voltage
      100-240 V
      Output voltage
      5 V
      Output current
      2 A
      Phase
      1 ~
      Frequency
      50-60 Hz
      Device performance data
      Charging time for an empty battery
      3,5 h
      Operating duration with a fully charged battery
      22 min
      Operating pressure
      0,7 MPa
      Water reservoir capacity
      8 l
      Suction height (max.)
      0,5 m
      Permissible ambient temperature
      0-40 °C
      Dimensions and weights
      Length
      296 mm
      Width
      291 mm
      Height of device with water reservoir
      240 mm
      Height of water reservoir
      178 mm
      Typical operating weight (CX)
      10,8 kg
      Determined values in acc. with EN 60335-2-79
      Sound level LpA
      68 dB(A)
      Uncertainty KpA
      2,5 dB(A)
      Sound power level LWA + Uncertainty KWA
      82 dB(A)
      <BackPage>

      2-2-SC-A5-GS-17339



      </BackPage>