LogoBR 30/4 C
  • General notes
  • Safety instructions
    • Hazard levels
  • Function
  • Intended use
  • Environmental protection
  • Control elements
    • Colour coding
    • Symbols on the device
  • Initial Start-Up
  • Operation
    • Filling the fresh water tank
    • Establishing the voltage supply
    • Cleaning
      • Normal soiling
      • Heavy soiling
      • Vacuuming in corners (only BR 30/4 C Adv)
    • Finishing cleaning
    • Emptying the waste water tank
    • Empty the fresh water tank
  • Transport
  • Storage
  • Care and maintenance
    • Maintenance plan
      • After work
      • Annually
    • Maintenance work
      • Replacing the suction bars
      • Replacing the roller brush
      • Cleaning the water distributor
      • Cleaning the suction pipe
      • Frost protection
  • Troubleshooting guide
    • Device does not start
    • Low water quantity
    • Fresh water tank drips when refilling
    • Poor suction performance
    • Unsatisfactory cleaning result
    • Brush does not rotate
    • Creaking noise, brush is not rotating
  • Accessories and spare parts
  • Accessories
  • Warranty
  • Technical data
    • 1.783-000.0
    • 1.783-220.0
    • 1.783-223.0
    • 1.783-224.0
  • EU Declaration of Conformity

      BR 30/4 C

      59785170 (09/26)

      General notes

      Read these original operating instructions and the enclosed safety instructions before using the device for the first time. Proceed accordingly.

      Keep both books for future reference or for future owners.

      Safety instructions

      Before using the device for the first time, read and observe these operating instructions and the accompanying brochure: Safety instructions for brush cleaning devices, No. 5.956-251.0.

      Hazard levels

      DANGER

      Indication of an imminent threat of danger that will lead to severe injuries or death.

      WARNING

      Indication of a potentially dangerous situation that may lead to severe injuries or death.

      CAUTION

      Indication of a potentially dangerous situation that may lead to minor injuries.

      ATTENTION

      Indication of a potentially dangerous situation that may lead to damage to property.

      Function

      This scouring and vacuum machine is used for wet cleaning of level floors. A working width of 300 mm and fresh and waste water tank capacities of 4 litres each enable effective cleaning of small areas.

      The mains operation allows high performance without working limits.

      Note

      The device can be equipped with various accessories to suit the respective cleaning order. Request a copy of our catalogue or visit our Internet website at www.kaercher.com.

      Intended use

      Use the device only in accordance with the information in these operating instructions.

      • Only use the device for cleaning hard surfaces that are not sensitive to moisture and polishing.

      • Use the device only at an ambient temperature between +5°C and +40°C.

      • Do not use the device for cleaning frozen floors (e.g. in cold stores).

      • Only equip the device with original accessories and spare parts.

      • Only use the device for cleaning indoor floors or covered areas.

      • Do not use the device for cleaning public traffic routes.

      • The device must not be used outdoors.

      • Never use the device in potentially explosive atmospheres.

      Environmental protection

      The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

      Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

      Notes on the content materials (REACH)

      Current information on content materials can be found at: www.karcher.de/REACH

      Control elements


      1. Handle
      2. Water pump switch
      3. Brush/suction operation button
      4. Carrying handle
      5. Waste water tank carrying handle
      6. Waste water tank
      7. Fresh water tank
      8. Fresh water tank lock
      9. Screen
      10. Cleaning head
      11. Pedal for suction bar lifting device
      12. Parking position release
      13. Suction pipe
      14. Suction pipe connection
      15. Suction nozzle (BR 30/4 C Adv only)
      16. Roller brush
      17. Suction bar
      18. Roller brush unlocking button
      19. Waste water tank cap
      20. Lock
      21. Filling level indicator
      22. Cable hook, rotatable
      23. Mains cable with mains plug
      24. Suction pipe handle (BR 30/4 C Adv only)

      Colour coding

      • Control elements for the cleaning process are yellow.

      • Control elements for maintenance and servicing are light grey.

      Symbols on the device

      Suction bar in the suction position
       
      Water pump on/off

      Initial Start-Up

      1. Insert the tube at the end of the handle into the opening on the device.


      2. Press the catches and push in the handle until it clicks into the device.

      3. Align the cables in the device.


      Operation

      Filling the fresh water tank

      CAUTION

      Risk of damage

      Use only recommended detergents. With other detergents, you are liable for the increased risk in terms of operational safety, risk of accident and reduced service life of the device. Use only detergents free of solvents, salt and hydrofluoric acid. Adhere to the safety instructions stated on the detergent packaging.

      Note

      Do not use strong foaming detergents.

      Observe dosing instructions.

      Recommended detergents:

      Application
      Detergent
      Dosing
      Alkaline maintenance cleaner
      APPROX. 50 C
      0.2...1.0%
      Acidic maintenance cleaner, for sanitary areas, swimming pools, etc. Removes limescale deposits.
      RM 738
      0.5...3.0%
      Wiper care EXTRA
      RM 780
      0.5...2.0%
      Acidic floor precleaner
      RM 751
      1.0...25%
      1. Remove the fresh water tank from the device.

      2. Open the fresh water tank cap.

      3. Fill with the water/detergent mixture. Maximum liquid temperature 50 °C.

      4. Fill with the water/detergent mixture. Maximum liquid temperature 60 °C.

      5. Close the fresh water tank cap.

      6. Insert the fresh water tank into the device.

      Establishing the voltage supply

      1. Swivel the lower cable hook upwards and remove the cable.

      2. Check the mains cable and the mains plug for damage and breakage. Have the replacement carried out only by customer service or a qualified electrician.

      3. Plug the mains plug into a mains socket.

      Cleaning

      DANGER

      Damage to the mains connection cable by rotating brushes

      Danger of death from electric shock.

      Do not allow the mains connection cable to come into contact with the rotating brushes.Always keep the cable outside the operating range of the brushes.

      ATTENTION

      Dry running due to empty fresh water tank

      Damage to the fresh water pump.

      Monitor the filling level indicator regularly during operation.Switch off the water pump switch immediately when the tank is empty.

      Normal soiling

      1. Move the suction bar lifting pedal to the "1/ON" position


      2. Set the main switch for brush/vacuum operation to "1".

      3. Switch on the water pump switch.

      4. Move the device over the surface to be cleaned.

      Heavy soiling

        ATTENTION

        Unsuitable cleaning method

        Damage to the floor covering.

        Only use the cleaning method for heavy soiling on suitable floors.Before use, check the suitability of the cleaning method in an inconspicuous area.
      1. Move the suction bar lifting pedal to the "0/OFF" position


      2. Carry out the cleaning as for normal soiling.

        The cleaning fluid remains on the surface to be cleaned and has time to take effect.

      3. Move the suction bar lifting pedal to the "suction" position and go over the area to be cleaned again.

      Vacuuming in corners (only BR 30/4 C Adv)

      1. Pull the suction pipe upwards by the handle, attach the suction nozzle and vacuum up dirt.

      2. Remove the nozzle, put the suction pipe back and lock the handle into place.

      Finishing cleaning

      1. Switch off the water pump.

      2. Push the device a short distance further to vacuum up the residual water.

      3. Set the brush/vacuum operation button to "0".

      4. Swivel the handle forwards and lock it into the parking position.

      5. Pull the mains plug out of the socket.

      Emptying the waste water tank

      Note

      When the waste water tank is full, the float closes the suction duct. The suction is interrupted. Empty the waste water tank.

      ATTENTION

      Dirt and detergent in the dirty water

      Environmental damage due to improper disposal.

      Observe the local waste water treatment regulations.
      1. Switch off the device.

      2. Straighten the device and lock it into the parking position.

      3. Remove the fresh water tank from the device.

      4. Swivel the carrying handle of the waste water tank downwards and remove the waste water tank.

      5. Lift the catch and remove the lid of the waste water tank.

      6. Pour out the dirty water.

      7. Rinse the waste water tank with clear water.

      8. Place the lid onto the waste water tank and lock it into place.

      9. Insert the waste water tank into the device.

      Empty the fresh water tank

      1. Remove the fresh water tank from the device.

      2. Open the fresh water tank cap.

      3. Pour out the cleaning fluid.

      4. Close the fresh water tank cap.

      5. Insert the fresh water tank into the device.

      Transport

      CAUTION

      High device weight

      Risk of injury and damage during transport.

      Be aware of the weight of the device during transport
      1. Swivel the handle forwards and lock it into the parking position.

        • Swivel the handle backwards and push the device.

        • Lift up the device by the carrying handle, and carry it.

      2. When transporting in vehicles, secure the device against rolling away, slipping and tipping according to the respectively applicable guidelines.

      Storage

      CAUTION

      Risk of injury and damage

      Be aware of the weight of the device during storage.

      Care and maintenance

      DANGER

      Electrical voltage and unintentional device start-up

      Risk of serious injury or life-threatening electric shock.

      Always switch the device off and disconnect the mains plug before working on the device.

      ATTENTION

      Leaking water

      Risk of damage to the device.

      Completely empty the waste water tank and the fresh water tank before maintenance work on the device.

      Maintenance plan

      After work

        ATTENTION

        Water jet and aggressive detergents

        Risk of damage to the device.

        Never spray the device with water.Do not use aggressive cleaning agents.
      1. Cleaning the waste water tank:

        1. Empty the waste water tank.

        2. Rinse out with water.

        3. Clean the seals between the waste water tank and the device.

      2. Rinsing the device:

        1. Fill the fresh water tank with clear water (without detergent).

        2. Operate the device for one minute with the brush irrigation switched on.

        3. Remove the residual water from the fresh water tank.

      3. Clean the exterior of the device using a damp cloth, wetted with a mild washing lye.

      4. Clean the suction bar, check for wear and replace if necessary (see “Maintenance work”).

      5. Check the brush for wear and tear, replace if required (see "Maintenance work").

      Annually

      1. Have the prescribed safety check carried out by a qualified electrician.

      Maintenance work

      Replacing the suction bars

      Note

      The suction bars are attached to the device with a snap-in connection and can be easily pulled off.

      1. Move the suction bar lifting pedal to the “1/ON” position.


      2. Remove the fresh water tank.

      3. Remove the waste water tank.

      4. Lay the device on its side.

      5. Pull the suction bars downwards to remove them.

      6. Insert the new suction bars and snap them into place.

      Replacing the roller brush

      1. Remove the fresh water tank.

      2. Remove the waste water tank.

      3. Lay the device on its side.

      4. Press the roller brush unlocking button, swivel the roller brush downwards and pull it off the driver.

      5. Fit the new roller brush onto the driver and engage on the opposite side.

      Cleaning the water distributor

      1. Take out the roller brush.

      2. Pull out the water distribution strip in the brush tunnel.


      3. Clean the irrigation channel and the openings in the water distribution strip under running water.

      Cleaning the suction pipe

      1. Remove the fresh water tank from the device.

      2. Swing the carrying handle of the waste water tank downwards and remove the waste water tank.

      3. Pull the suction pipe connection out of the back of the device and swing both ends of the suction pipe out.

        The suction pipe is disconnected and both ends are accessible for cleaning.


      4. Pull the suction bars downwards to remove them.

        The suction duct in the cleaning head is accessible for cleaning.


      5. Flush the suction hose and suction duct with water or pull or push out blockages using a blunt object.

      Frost protection

      If there is a risk of frost:

      1. Empty the fresh water tank and the waste water tank.

      2. Park the device in a frost-protected room.

      Troubleshooting guide

      DANGER

      Electrical voltage and unintentional device start-up

      Risk of serious injury or life-threatening electric shock.

      Always switch the device off and disconnect the mains plug before working on the device.

      ATTENTION

      Leaking water

      Risk of damage to the device.

      Completely empty the waste water tank and the fresh water tank before maintenance work on the device.

      Contact Customer Service in the case of malfunctions that cannot be corrected using these instructions.

      • Device does not start 

      • Low water quantity 

      • Fresh water tank drips when refilling 

      • Poor suction performance 

      • Unsatisfactory cleaning result 

      • Brush does not rotate 

      • Creaking noise, brush is not rotating 

      Device does not start

      Cause:

      Remedy:

      • Check that the mains plug is plugged in.

      Remedy:

      • Check if the roller brush is blocked by a foreign body and remove the foreign body if necessary.

      Low water quantity

      Cause:

      Remedy:

      • Check the fresh water level, top up tank if necessary.

      Remedy:

      • Open the fresh water tank cap. If a vacuum is detected in the tank when opening it, clean the ventilation valve in the fresh water tank cap.

      Remedy:

      • Clean the water distributor, see Cleaning the water distributor

      Remedy:

      • Remove the fresh water tank and check the filter for contamination. If necessary, remove the filter and clean it.

      Remedy:

      • Pull the valve with the filter off the fresh water tank and rinse it in lukewarm water.


      Remedy:

      • Clean the sieve in the cleaning head.

      Fresh water tank drips when refilling

      Cause:

      Remedy:

      • Pull the valve with the filter off the fresh water tank and rinse it in lukewarm water.


      Poor suction performance

      Cause:

      Remedy:

      • Empty the waste water tank.

      Remedy:

      • Engage the waste water tank in the device.

      Remedy:

      • Clean the seals between the waste water tank and the cover, check for leaks and replace if necessary.

      Remedy:

      • Check the seals between the waste water tank lid and the device. If the seals are damaged, contact customer service.

      Remedy:

      • Check whether the suction bars are engaged in the cleaning head.

      Remedy:

      • Clean blocked suction bars.

      Remedy:

      • worn suction bars: Swap the front and rear suction bars with each other. If both suction bars are worn, insert new suction bars.

      Remedy:

      • Check whether both suction pipe parts are correctly connected to the suction pipe connection.

      Remedy:

      • Check the suction pipe and the suction duct in the cleaning head for blockages, remove any blockages if necessary, see Cleaning the suction pipe.

      Remedy:

      • Check whether the cable is laid flat behind the tanks.

      Unsatisfactory cleaning result

      Cause:

      Remedy:

      • Check the roller brush for wear and tear, replace if required.

      Brush does not rotate

      Cause:

      Remedy:

      • Check if the roller brush is blocked by a foreign body and remove the foreign body if necessary.

      Creaking noise, brush is not rotating

      Cause:

      Remedy:

      • The slip clutch has triggered. Switch off the device, check/clean the roller brush.

      Accessories and spare parts

      Only use original accessories and original spare parts; they ensure safe and fault-free operation of the device.

      Information on accessories and spare parts can be found at www.karcher.com.

      Accessories

      Accessories
      Description
      Order number
      Roller brush, red
      Universal brush for all floor coverings
      4.762-428.0
      Roller brush, orange
      Special brush for textured floors such as safety tiles or joints
      4.762-484.0
      Roller brush, white
      Soft brushes for sensitive floors and for polishing
      4.762-452.0
      Roller brush, blue
      Soft brush for fibre-deep cleaning of carpets
      4.762-499.0
      Microfiber roller
      Cleaning brush made of microfibre with particularly high cleaning performance. Especially for fine stone tiles.
      4.762-453.0
      Replacement suction lip
      Made of natural rubber. 2 pieces required.
      4.777-320.0
      Replacement suction lip, oil-resistant
      For oil and grease-based dirt, for example in kitchens and workshops. 2. Pieces required
      4.777-324.0
      Carpet cleaning set
      Fibre-deep cleaning of textile surfaces. Consisting of roller brushes, 2 suction bars, 1 litre of cleaning agent concentrate, 500 ml of stain remover
      2.783-005.0

      Warranty

      The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing flaw is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

      You can find more detailed information at: www.karcher.com/dealersearch

      Further warranty information (if available) can be found in the service area of your local KÄRCHER website under "Downloads".

      Technical data

      • 1.783-000.0 

      • 1.783-220.0 

      • 1.783-223.0 

      • 1.783-224.0 

      1.783-000.0

      Electrical connection
      Mean power consumption
      820 W
      Mains voltage
      220-240 V
      Phase
      1 ~
      Power frequency
      50-60 Hz
      Protection type
      IPX4
      Protection class
      I
      Performance data
      Suction performance, air quantity
      26 l/s
      Suction performance, vacuum
      13 kPa
      Theoretical surface coverage
      200 m2/h
      Fresh/waste water tank volume
      4 l
      Cleaning brushes
      Working width
      300 mm
      Brush diameter
      60 mm
      Brush speed
      1450 rpm
      Dimensions and weights
      Length x width x height
      390 x 335 x 1180 mm
      Approved total weight
      16 (Adv 16,5) kg
      Transport weight
      12 (Adv 12,5) kg
      Determined values according to EN 60335-2-72
      Hand-arm vibration ahv
      0,8 m/s2
      Uncertainty hand-arm vibration K
      0,2 m/s2
      Repeated shock vibrations pF
      20 m/s2
      Uncertainty repeated shock vibrations K
      - m/s2
      Sound power level LwA
      85 dB(A)
      Uncertainty KWA
      1 dB(A)
      Sound pressure level LpA
      72 dB(A)
      Uncertainty sound pressure level KpA
      1 dB(A)

      1.783-220.0

      Electrical connection
      Mean power consumption
      820 W
      Mains voltage
      220-240 V
      Phase
      1 ~
      Power frequency
      50-60 Hz
      Protection type
      IPX4
      Protection class
      I
      Performance data
      Suction performance, air quantity
      26 l/s
      Suction performance, vacuum
      13 kPa
      Theoretical surface coverage
      200 m2/h
      Fresh/waste water tank volume
      4 l
      Cleaning brushes
      Working width
      300 mm
      Brush diameter
      60 mm
      Brush speed
      1450 rpm
      Dimensions and weights
      Length x width x height
      390 x 335 x 1180 mm
      Approved total weight
      16 (Adv 16,5) kg
      Transport weight
      12 (Adv 12,5) kg
      Determined values according to EN 60335-2-72
      Hand-arm vibration ahv
      0,8 m/s2
      Uncertainty hand-arm vibration K
      0,2 m/s2
      Repeated shock vibrations pF
      20 m/s2
      Uncertainty repeated shock vibrations K
      - m/s2
      Sound power level LwA
      85 dB(A)
      Uncertainty KWA
      1 dB(A)
      Sound pressure level LpA
      72 dB(A)
      Uncertainty sound pressure level KpA
      1 dB(A)

      1.783-223.0

      Electrical connection
      Mean power consumption
      750 W
      Mains voltage
      220-240 V
      Phase
      1 ~
      Power frequency
      50-60 Hz
      Protection type
      IPX4
      Protection class
      I
      Performance data
      Suction performance, air quantity
      26 l/s
      Suction performance, vacuum
      13 kPa
      Theoretical surface coverage
      200 m2/h
      Fresh/waste water tank volume
      4 l
      Cleaning brushes
      Working width
      300 mm
      Brush diameter
      60 mm
      Brush speed
      1450 rpm
      Dimensions and weights
      Length x width x height
      390 x 335 x 1180 mm
      Approved total weight
      16 (Adv 16,5) kg
      Transport weight
      12 (Adv 12,5) kg
      Determined values according to EN 60335-2-72
      Hand-arm vibration ahv
      0,8 m/s2
      Uncertainty hand-arm vibration K
      0,2 m/s2
      Repeated shock vibrations pF
      20 m/s2
      Uncertainty repeated shock vibrations K
      - m/s2
      Sound power level LwA
      85 dB(A)
      Uncertainty KWA
      1 dB(A)
      Sound pressure level LpA
      72 dB(A)
      Uncertainty sound pressure level KpA
      1 dB(A)

      1.783-224.0

      Electrical connection
      Mean power consumption
      750 W
      Mains voltage
      220-240 V
      Phase
      1 ~
      Power frequency
      50-60 Hz
      Protection type
      IPX4
      Protection class
      I
      Performance data
      Suction performance, air quantity
      26 l/s
      Suction performance, vacuum
      13 kPa
      Theoretical surface coverage
      200 m2/h
      Fresh/waste water tank volume
      4 l
      Cleaning brushes
      Working width
      300 mm
      Brush diameter
      60 mm
      Brush speed
      1450 rpm
      Dimensions and weights
      Length x width x height
      390 x 335 x 1180 mm
      Approved total weight
      16 (Adv 16,5) kg
      Transport weight
      12 (Adv 12,5) kg
      Determined values according to EN 60335-2-72
      Hand-arm vibration ahv
      0,8 m/s2
      Uncertainty hand-arm vibration K
      0,2 m/s2
      Repeated shock vibrations pF
      20 m/s2
      Uncertainty repeated shock vibrations K
      - m/s2
      Sound power level LwA
      85 dB(A)
      Uncertainty KWA
      1 dB(A)
      Sound pressure level LpA
      72 dB(A)
      Uncertainty sound pressure level KpA
      1 dB(A)

      EU Declaration of Conformity

      We hereby declare that the product named below complies with the relevant provisions of the directives and regulations listed. This declaration is invalidated by any changes made to the product that are not approved by us. The manufacturer shall bear sole responsibility for issuing of this declaration of conformity.

      Product: Floor cleaner

      Type: 1.783-xxx

      Directives and Regulations

      2006/42/EC (+2009/127/EC) (until 19/01/2027) (EU) 2023/1230 (from 20/01/2027)

      2014/30/EU

      2011/65/EU

      Harmonised standards used

      EN 60335-1

      EN 60335-2-72

      EN 62233: 2008

      EN 55014-1: 2006+A1: 2009+A2: 2011

      EN 55014-2: 1997+A1: 2001+A2: 2008

      EN 61000-3-2: 2014

      EN 61000-3-3: 2013

      EN IEC 63000: 2018

      Name and address

      Documentation supervisor:

      S. Reiser

      Alfred Kärcher SE & Co. KG

      Alfred-Kärcher-Str. 28 - 40

      71364 Winnenden (Germany)

      Tel.: +49 7195 14-0

      Fax: +49 7195 14-2212


      Winnenden, 2026/10/01

      The undersigned act on behalf of and with the authority of the Board of Directors.

      Alfred Kärcher SE & Co. KG

      Alfred-Kärcher-Str. 28 - 40

      71364 Winnenden (Germany)

      Ph.: +49 7195 14-0

      Fax: +49 7195 14-2212

      UK Declaration of Conformity

      We hereby declare that the product named below complies with the relevant provisions of the directives and regulations listed. This declaration is invalidated by any changes made to the product that are not approved by us. The manufacturer shall bear sole responsibility for issuing of this declaration of conformity.

      Product: Floor cleaner

      Type: 1.783-xxx

      Directives and Regulations

      S.I. 2008/1597 (as amended)

      S.I. 2016/1091 (as amended)

      S.I. 2012/3032 (as amended)

      Designated standards used

      EN 60335-1

      EN 60335-2-72

      EN 62233: 2008

      EN 55014-1: 2006+A1: 2009+A2: 2011

      EN 55014-2: 1997+A1: 2001+A2: 2008

      EN 61000-3-2: 2014

      EN 61000-3-3: 2013

      EN IEC 63000: 2018

      Name and address

      Documentation supervisor:

      S. Reiser

      Alfred Kärcher SE & Co. KG

      Alfred-Kärcher-Str. 28 - 40

      71364 Winnenden (Germany)

      Tel.: +49 7195 14-0

      Fax: +49 7195 14-2212


      Winnenden, 2026/10/01

      The undersigned act on behalf of and with the authority of the Board of Directors.

      Alfred Kärcher SE & Co. KG

      Alfred-Kärcher-Str. 28 - 40

      71364 Winnenden (Germany)

      Ph.: +49 7195 14-0

      Fax: +49 7195 14-2212

      <BackPage>

       

        

       



      </BackPage>